Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

It literally came out last night

I know, but maybe someone had it 3D printed at home...

This is not only a custom Layer.
This is totally a new Beyblade!
For one of the impressive beyblade of Metal series, I made a Burst version!
Earth Aquila. E. K!

Layer-Earth Aquila

Spoiler (Click to View)

Disc-End

Spoiler (Click to View)

Driver-Kernel

Spoiler (Click to View)

Video

Spoiler (Click to View)

Download files

awesome bey,  hope u make a remake of burn phoenix someday anyways the main thing i wanted to ask was wont kernel damage the stadium?  It looks very sharp

---

Fav cho-Z combos
[\spoiler]
cR with A level chip 7 Revolve
rP with A level chip 10 Cross Atomic
zA with A level chip 0 Bump Destroy
hS with A level chip 7 Glaive Bearing
vL with A level chip 0 Reach Jolt
bL with A level chip 0 Glaive Variable(worn)

Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

It is so heavy now so that is very good at performance... But I don't think this is too early to say it is good. I will make another one that is totally plastic, to see how it really works.

---

Are there any other Cho-Z remakes you're planning to do? Like a Zeus or a Spriggan?

FYI, not trying to pester you. I'm just curious about your future plans haha.

---

Eh, I will think of something to put here...

... later ;)

Are there any other Cho-Z remakes you're planning to do? Like a Zeus or a Spriggan?

FYI, not trying to pester you. I'm just curious about your future plans haha.

I have someone making X spriggan based on your design ^^

---

~Thunder

The Kinetic driver and especially that Xplode driver are extremely impressive, Xplode could easily have fooled anyone into believing it was an already existing product. Good job!

---

My Cho-Z Reaper Deathscyther .12.Cr concept render, click below to see!

Spoiler (Click to View)

No I don't plan on doing more yet.

I should probably go back to making fan custom Zero G beyblade concepts again

How do you guys design your beyblades? Is it something like a website or a program, or do you just design it by hand and have it scanned?

Are there any other Cho-Z remakes you're planning to do? Like a Zeus or a Spriggan?

FYI, not trying to pester you. I'm just curious about your future plans haha.

I have someone making X spriggan based on your design ^^

Yo dats eill af yo can't wait to see it

---

Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

It is so heavy now so that is very good at performance... But I don't think this is too early to say it is good. I will make another one that is totally plastic, to see how it really works.

Hey CrazyAries  I was curious,
If u ever have time in the future could u take my Dragoon God Evolution layer
I'm getting made
And turn it in to a Cho zetsu bey for everyone to see and enjoy ??? I think it would be dope it u did a Cho zetsu Dragoon

Beautiful work once again! You never fail to impress me @[CrazyAries].

I'd love to get some of this newer stuff printed but it's costed me a lot so I have to take a break (for now) 

If it's not too much to ask, what site or service did you use to 3D print the parts for Cosmic Odin's layer?

---

My YouTube Channel 
My Facebook Page

can you print and send the one you made me?
I don't have a 3D printer.....

If it's not too much to ask, what site or service did you use to 3D print the parts for Cosmic Odin's layer?

Kevo uses Shapeways

Here is a new custom bey. It's called Zone Jupiter. Zigzag. Quell. (zJ.Z.Ql)
It's perhaps the last custom beyblade this summer break. I almost used up all my money (the metal workshop is really expensive...) and I need to prepare for the new semester.

Layer - Zone Jupiter (zJ)

Spoiler (Click to View)

This design is similar to Z2 and gZ, that use metal balls in the layer. (Jupiter and Zeus are basically the same god but different name in different culture)
What is different is that the metal balls in this layer is much larger so that they should be more effective, and they are exposed so that can directly hit opponents to improve both attack and defense.
Cho Z Ability: Satellite Zone
Type: Balance


There are two main parts and some metal balls for this layer. For the two main parts, the files zj1 and zj2 will be needed. You can directly 3D print both parts, and if you like, you could make them different material. That's up to you (But I don't suggested you to make them metal, since that could make this beyblade too heavy and may damage your launcher).
There are two sizes of metal balls on this layer, that one is 8mm in diameter and one is 6mm. 2 of 8mm balls are needed, and the amount of 6mm could vary as you like. 
There are the files of those two metal balls, but I suggest you to directly purchase them since that would be much cheaper.
4 M2*5 screws will be needed (or you can get them from any official release).

================================================================================

Disc - Zigzag (Z)

Spoiler (Click to View)

You will need a Magnum, Jerk or Polish, and get the metal part from them for this disc. you could 3D print this part and I suggest you to use rubber. You can then assemble this part with the metal part you get from disc M/J/P

================================================================================

Driver - Quell (Ql)

Spoiler (Click to View)

This Driver is a combination of Bearing and βite.
The white ball tip is made of rubber, so it can better catch the stadium and will not be easily knocked off the stadium.
Its bearing inside could improve its stamina (as you know, rubber tips has horrible stamina due to the friction, but the bearings could help).
And it is very tall. It's significantly higher than Volcanic and the burst bey with this driver could be as tall as the 230WD combos in metal series.


There are 4 files to make this driver. The tip(Quell4) is supposed to be Rubber but you can make it plastic or any material you like. You will need a M2*6 screw, two 4*7*2.5 bearings and a M2*5*0.3 gasket to assemble it.
You need to get the white ring and the spring from another driver. (Warning: This may totally destroy that driver.)
Also, you would need another two M2*8 screws to finally complete this driver.

================================================================================

Video

Spoiler (Click to View)

Download

---

Here is a new custom bey. It's called Zone Jupiter. Zigzag. Quell. (zJ.Z.Ql)
It's perhaps the last custom beyblade this summer break. I almost used up all my money (the metal workshop is really expensive...) and I need to prepare for the new semester.

Layer - Zone Jupiter (zJ)

Spoiler (Click to View)

This design is similar to Z2 and gZ, that use metal balls in the layer. (Jupiter and Zeus are basically the same god but different name in different culture)
What is different is that the metal balls in this layer is much larger so that they should be more effective, and they are exposed so that can directly hit opponents to improve both attack and defense.
Cho Z Ability: Satellite Zone
Type: Balance


There are two main parts and some metal balls for this layer. For the two main parts, the files zj1 and zj2 will be needed. You can directly 3D print both parts, and if you like, you could make them different material. That's up to you (But I don't suggested you to make them metal, since that could make this beyblade too heavy and may damage your launcher).
There are two sizes of metal balls on this layer, that one is 8mm in diameter and one is 6mm. 2 of 8mm balls are needed, and the amount of 6mm could vary as you like. 
There are the files of those two metal balls, but I suggest you to directly purchase them since that would be much cheaper.
4 M2*5 screws will be needed (or you can get them from any official release).

================================================================================

Disc - Zigzag (Z)

Spoiler (Click to View)

You will need a Magnum, Jerk or Polish, and get the metal part from them for this disc. you could 3D print this part and I suggest you to use rubber. You can then assemble this part with the metal part you get from disc M/J/P

================================================================================

Driver - Quell (Ql)

Spoiler (Click to View)

This Driver is a combination of Bearing and βite.
The white ball tip is made of rubber, so it can better catch the stadium and will not be easily knocked off the stadium.
Its bearing inside could improve its stamina (as you know, rubber tips has horrible stamina due to the friction, but the bearings could help).
And it is very tall. It's significantly higher than Volcanic and the burst bey with this driver could be as tall as the 230WD combos in metal series.


There are 4 files to make this driver. The tip(Quell4) is supposed to be Rubber but you can make it plastic or any material you like. You will need a M2*6 screw, two 4*7*2.5 bearings and a M2*5*0.3 gasket to assemble it.
You need to get the white ring and the spring from another driver. (Warning: This may totally destroy that driver.)
Also, you would need another two M2*8 screws to finally complete this driver.

================================================================================

Video

Spoiler (Click to View)

Download

Nice, you completed it and as expected it's a work of art as always with impressive performance and engineering, good job also hope everything goes well for you with the new semester around the corner.

Also just out of curiousity, what paint do you use? Because I'm guessing it's pretty resistant in terms of when your just carrying it around and what not.

---

My YouTube Channel 
My Facebook Page

Nice, you completed it and as expected it's a work of art as always with impressive performance and engineering, good job also hope everything goes well for you with the new semester around the corner.

Also just out of curiousity, what paint do you use? Because I'm guessing it's pretty resistant in terms of when your just carrying it around and what not.

I used the paint of Tamiya. But it may not be so resistant as you expected.

---

Nice, you completed it and as expected it's a work of art as always with impressive performance and engineering, good job also hope everything goes well for you with the new semester around the corner.

Also just out of curiousity, what paint do you use? Because I'm guessing it's pretty resistant in terms of when your just carrying it around and what not.

I used the paint of Tamiya. But it may not be so resistant as you expected.

Thanks, and it really doesn't have to be that resistant but I'll either go with that or model master acrylic which is quite resistant.

---

My YouTube Channel 
My Facebook Page

This is all amazing! Hopefully I can make my designs, do you guys use 3D models or do you just make the digital designs?

I've complete the 3D model of Blitz Unicorno in Burst format. But I haven't make it real because I used too much money on previous beys and now I don't have enough money...
I prepared a Layer and a Driver for Blitz Unicorno and I think Disc Triple will be a good choice so I didn't design the disc (Ans I think I have already complete the Alphabet for Disc...)

Layer - Blitz Unicorno (bU)

Spoiler (Click to View)

One thing that may disapoint you is that I didn't add the function of mode change on this layer. I think Assault mode is the one that people usually use so I just make it in Assault mode.

Driver - Dive (Dv)

Spoiler (Click to View)

The red tip is rubber. This Driver is basically a Burst format of RSF.
Also, In order to realize the feature of Track 100, I made this driver short. So the bey would be good at Upper attack, but you need to be careful as the disc may touch the stadium.

File Download

---

This is sicc CrazyAries good job man i like it dude!

I've complete the 3D model of Blitz Unicorno in Burst format. But I haven't make it real because I used too much money on previous beys and now I don't have enough money...
I prepared a Layer and a Driver for Blitz Unicorno and I think Disc Triple will be a good choice so I didn't design the disc (Ans I think I have already complete the Alphabet for Disc...)

Layer - Blitz Unicorno (bU)

Spoiler (Click to View)

One thing that may disapoint you is that I didn't add the function of mode change on this layer. I think Assault mode is the one that people usually use so I just make it in Assault mode.

Driver - Dive (Dv)

Spoiler (Click to View)

The red tip is rubber. This Driver is basically a Burst format of RSF.
Also, In order to realize the feature of Track 100, I made this driver short. So the bey would be good at Upper attack, but you need to be careful as the disc may touch the stadium.

File Download

Looking good. Mind if I give a little feedback? If the disk has a risk of scraping could you solve that problem with a built in disk gimmick? One of each set of contact points could act like the disk and move with each click. This would give is a pseudo auto mode change.

I don't know how hard this idea would be to make but I think you could do it.

edit: on second look at the layer I noticed that it would take a lot of editing to get it to work so the idea may not work.

---

Highly Observant Hasbro Blader.

---

I would love to see the old Kelloggs attack rings redone for burst, mainly the 3 pointed ones 

could someone here make this into a burst layer, I just cant get this template 100% even of all sides 

https://sta.sh/01wvapoz1h2z

---

if your respectful to Me, then Il do the same and be respectful to you.

there is no such thing as perfection, for with out flaws we can not improve.

managed to make it even with a bit of fiddling, and math
https://sta.sh/01ckh8tnx6pm

---

if your respectful to Me, then Il do the same and be respectful to you.

there is no such thing as perfection, for with out flaws we can not improve.

managed to make it even with a bit of fiddling, and math
https://sta.sh/01ckh8tnx6pm

You could PM Xandork about this idea. The requirements and price are on his thread: https://worldbeyblade.org/Thread-Cho-X-Custom-3D-Beys. He makes custom beys, so maybe he could make the bey that you designed too.

managed to make it even with a bit of fiddling, and math
https://sta.sh/01ckh8tnx6pm

You could PM Xandork about this idea. The requirements and price are on his thread: https://worldbeyblade.org/Thread-Cho-X-Custom-3D-Beys. He makes custom beys, so maybe he could make the bey that you designed too.

his price is rather steap, yes its for a custom part, but for £30 or so, it just doesnt feel right, they also only had 2 examples of their work that I could see, and neather were to my liking, that isnt to say their bad, but the results arent my taste, plus I already know the other parts I plan to use, bearing drive or revive I think it was that come was ragnarok from hasbro (I know it doesnt come with bearing but I dont know the name of the other driver and with hasbro changing the names its just stupid) and well, this was just an idea that would have been cool to see, I can always fall back on using a wyvron 2 layer.

thank you for your suggestion, but I will decline it

---

if your respectful to Me, then Il do the same and be respectful to you.

there is no such thing as perfection, for with out flaws we can not improve.

Can you make a custom bey with spikes and swords for me