[Answered]  Hell Salamander Slightly Jammed on Launcher, Normal?

I own 2 authentic Takara Tomy Hell Salamanders, and they don't really fit on my launcher well. I own a Takara Tomy Light Launcher L, my Bloody Longinus fits perfectly on it, Salamander is the only one having this problem. It's not significant, but I'm scared that the plastic of the slots for the launcher will break with constant use. 
It's normal. That happens to some of my beys too. However, you should launch a bit more carefully with Salamander, since if it gets jammed slightly, it might cause an insta-burst if you launch too hard.
(Apr. 20, 2019  7:01 PM)TheBladingCow Wrote: It's normal. That happens to some of my beys too. However, you should launch a bit more carefully with Salamander, since if it gets jammed slightly, it might cause an insta-burst if you launch too hard.

Thank you ! Since nobody talked about it, I thought perhaps I had a defect. I'm disappointed that Takara Tomy has never fixed this issue in the newer releases of Hell Salamander.
You're using a decently heavy bey on a light launcher. Expect problems.
(Apr. 20, 2019  9:44 PM)Rainy Sunset Wrote:
(Apr. 20, 2019  7:01 PM)TheBladingCow Wrote: It's normal. That happens to some of my beys too. However, you should launch a bit more carefully with Salamander, since if it gets jammed slightly, it might cause an insta-burst if you launch too hard.

Thank you ! Since nobody talked about it, I thought perhaps I had a defect. I'm disappointed that Takara Tomy has never fixed this issue in the newer releases of Hell Salamander.

You're welcome!
does anyone have an answer to the modes being stuck on the attack mode? I tried to prise it open with a knife, a fork a and a screwdriver, nothing works. The screws that they use for Hell Salamander aren't the normal type you'd normally use. I'm wondering if anyone has any answers?

(Dec. 31, 2019  10:44 PM)BeybladeLedgend Wrote: does anyone have an answer to the modes being stuck on the attack mode? I tried to prise it open with a knife, a fork a and a screwdriver, nothing works. The screws that they use for Hell Salamander aren't the normal type you'd normally use. I'm wondering if anyone has any answers?

Don’t revive a dead thread. Next time make a thread for this. Also have you tried pulling the tabs on the driver up? Also it sounds like you might have a fake beyblade.
No I did try that. It worked for a while at first, but now it doesn't... Also, I found the thread for this, sorry to bother you.
(Dec. 31, 2019  10:51 PM)BeybladeLedgend Wrote: No I did try that. It worked for a while at first, but now it doesn't... Also, I found the thread for this, sorry to bother you.

Have you considered the fact that it may be a fake? What brand is it?
Sadly, I never got hS, what spin direction is it?

(Dec. 31, 2019  10:56 PM)BuilderROB Wrote:
(Dec. 31, 2019  10:51 PM)BeybladeLedgend Wrote: No I did try that. It worked for a while at first, but now it doesn't... Also, I found the thread for this, sorry to bother you.

Have you considered the fact that it may be a fake? What brand is it?

He said they are two authentic TT beys.
(Dec. 31, 2019  11:02 PM)YishYash Wrote: Sadly, I never got hS, what spin direction is it?

(Dec. 31, 2019  10:56 PM)BuilderROB Wrote: Have you considered the fact that it may be a fake? What brand is it?

He said they are two authentic TT beys.

Left spin
(Dec. 31, 2019  11:03 PM)JoMario67 Wrote:
(Dec. 31, 2019  11:02 PM)YishYash Wrote: Sadly, I never got hS, what spin direction is it?


He said they are two authentic TT beys.

Left spin

Thanks!
i checked that Beyblade Wiki on FANDOM and there's nothing there about it too...

so what do you think?
All of you just revived a dead thread, that is not allowed.
(Dec. 31, 2019  11:11 PM)lilphilyb Wrote: All of you just revived a dead thread, that is not allowed.

I mentioned that in my first reply to him.