World Beyblade Organization by Fighting Spirits Inc. Beyblade Discussion Beyblade General

Manufactoring Errors with Your Bey

Aug. 04, 2011  2:40 PM
 
(Aug. 04, 2011  12:47 PM)MFB Mad Master Wrote: I bought Galaxy Pegasus and got a PURPLE Galaxy Wheel. Thats a good thing only purple one in existence.

wow can you post a picEee
Aug. 04, 2011  2:55 PM
 
I doubt it is Purple, post a pic as Tokyo boyy said. Maybe it is blue and you thought it is purple?
Aug. 05, 2011  3:22 PM
 
I bought a metal masters earth virgo (which is an amazing bey just to be off topic) and on the side it said Burn Fireblaze. it was no problem, i mean i would've thrown it away anyway but i was just shocked
Aug. 15, 2011  8:57 AM
 
I would like to see this perple Galaxy, I must admit though, it would be pretty awesome!!
Aug. 17, 2011  4:31 PM
 
Purple? PURPLE? Gotta see it! I got my R2F... And it has a deep hole...
Aug. 17, 2011  7:36 PM
 
I'm not sure if this qualifies as a Manufacturing Error, but I have two GB145, and one of them seems to very consistently out-perform the other, almost entirely regardless of setup. I've spent the afternoon testing them, and here's what I came up with on my most "precise" tests:

Hasbro Plastics-Era Blizzard Bowl Stadium
2x Red Hasbro String Launcher
1x Earth Pegasus GB145CS
1x Thunder Pegasus GB145WD

One of the GB145s is solid yellow, the other transluscent gray-ish.

Earth Pegasus GB145CS(Yellow) Thunder Pegasus GB145WD(Gray)
5 - 0

So, I switched them.

Earth Pegasus GB145CS(Gray) Thunder Pegasus GB145WD(Yellow)
1 - 4

My launching was as consistent as it could possibly be, and the CS was always being launched in Defense-mode. Every time the Yellow won, it continued spinning for about 30~45 seconds after victory. All victories were by Out-Spin.

I'm not sure what could possibly cause this sort of thing, as the gray one looks and feels identical. I'm not even sure if this is the right place to post this, but it feels like there's something wrong with the product itself.
Aug. 17, 2011  7:42 PM
 
Hasbro Strikes again.
I found a galaxy at my TRU with a regular RF.
Aug. 17, 2011  7:44 PM
 
I didn't buy the beyblade but at TRU there was a Ray Striker with a Cyber wheel.
Aug. 17, 2011  10:37 PM
 
My EWD doesn't clip onto tracks at all. Its so loose that so can take it off with your fingers using barely any effort Unhappy And its the one on my nightmare rex from the SBS. Oh well, EDS is just as good...
Aug. 18, 2011  9:46 AM
 
(Aug. 04, 2011  2:55 PM)Blitz Unicorno Wrote: I doubt it is Purple, post a pic as Tokyo boyy said. Maybe it is blue and you thought it is purple?

He probably made that up, and when we tell him to post a pic he will just paint it.
Plus, it could be fake anyway cause he has a fake ray gil and I doubt that he can get something as rare as Sol Blaze so its prob fake as well.
Aug. 18, 2011  6:54 PM
 
(Jul. 14, 2011  7:38 PM)PunkBlader Wrote: I got a bey with a facebolt already broke. I think since it was a 2 pack when they assembled it whoever did it did it too tightly. I just got my money back and that was that.
ditto here, cept i coulnt return Unhappy
Sep. 01, 2011  9:48 PM
 
Has anybody got a GOOD manufactoring error before?
Sep. 01, 2011  9:53 PM
 
I know one of my dark wheels is much heavier than the others I have.

Hint: None of them are from Takara or Sonokong.
Sep. 01, 2011  10:47 PM
 
My firend got a R2F with A METEO LDRAGO!!!
Sep. 04, 2011  4:48 AM
 
I just looked at my flame sag ( Hasbro of course ) and where it says BEYBLADE at one end, at the other it says BLYBEADE L and E switched around
Sep. 04, 2011  6:38 PM
 
My hasbro RF that came with storm pegasis tip was a bit bent and i couldnt even place it back...but its finally working thanks to a lot of grinding runs on the stadiums...its levelled...also i got an unfinished ray (mold 1) wheel and a fragile D125 that broke its bottom ridges from a single use with a sonokong ray unicorno...its fine i fixed it... Smile
Sep. 04, 2011  6:49 PM
 
I have a Basalt with an air gap. It weighs 45 grams and you can see two small holes. its so bad that a single hit usually makes it so unbalance that it dies...
Sep. 04, 2011  7:09 PM
 
WD145 seems to be deformed T^T ... its event limited bey ...
Sep. 04, 2011  7:43 PM
 
(Sep. 04, 2011  7:09 PM)Fonspark Wrote: WD145 seems to be deformed T^T ... its event limited bey ...

Whoa that is a serious defect at the wrong place... Smile
Sep. 05, 2011  2:19 PM
 
My Jade is a little bit loose, though it is negligible.
Sep. 22, 2011  6:47 AM
 
The Launcher from my Hasbro galaxy pegasis was seriously stuffed up, like it was used for ages before they packaged it, as it gave crazily weak shots...
Sep. 22, 2011  8:14 AM
 
(Sep. 22, 2011  6:47 AM)Dracon Wrote: The Launcher from my Hasbro galaxy pegasis was seriously stuffed up, like it was used for ages before they packaged it, as it gave crazily weak shots...

It could just be a dislodged gear inside the Launcher from being bumped around during packaging - I recall having something similar happen during Plastics. Got a shooter with the spring displaced inside of it, but it was easy to fix.
Sep. 30, 2011  9:59 AM
 
i cant help but notice that most of the manfacturing errors are from hasbro parts
yeah better quality my A@#
any wasy i found a hasbro grand cetus only it wasnt grand it was ray cetus there was a ray wheel inside it
i surpose you call this good since ray is better that grand but meh i didnt but it though i had no money
Sep. 30, 2011  1:35 PM
 
Eh, my little bro ( BBX )'s Aqaurio 105F instrution booklet has the track "W125" in it...............
Sep. 30, 2011  2:12 PM
 
I have recently purchased another Dark Bull H125SD(Hasbro Version) from Walmart and the beylauncher was broken inside. That's the most common manufacturing error I run into the most. This makes me feel proud to own a string launcher.
Prev
Page 6
Next