I found my own way on cleaning your beyblade. Also one reason to clean your beyblade is because dirt slows them down slowly so their performace rate would be down.
Materials:
-Sink
-Water hot
-A small container that can hold hot water
-Any liquid soap any kind
-Paper Towels
( optional )
-2 rags
-Brasso-they can be found at fred meyer at the grocery section
-A paper plate to put your beyblades on and letting them rest for a while
-First off you dis-asemble your beyblade line up the parts from bolt to bottom to see all the parts you have and won't lose track any of your parts. The next thing is grab the bottom and track parts of the beyblade ( the two parts at the bottom of the bey ) You can also grab the clear wheel of the bey if you don't really care of the stickers coming off. Go to your sink and put of your hands and put liquid hand soap on your beyblade parts like your washing your hands. Your two hands scrubbing each other like washing hands with the parts inside and with soap don't add water yet. Once u Scrubbed them enough use the water that's mid-hot so you won't burn your hands. Make sure the parts have no soap in them. Then Fill up your container with hot water, enough to sink the parts. Then put your parts in. While their in the water. This is optional cleaning your fusion wheel if you want too but i mostly do it. Fusion wheels i think are made out of stainless steel. So i use brasso it cleans and polishes so it's perfect. Grab one rag and put the brasso on it and put it on your beyblade. Then once it's on the sides and bottom and top clean the brasso with the dry rag. And there you go your polished fusion wheel. Ok let's get back to your parts that are in the water. Grab your parts and get the water off using your paper towels. Ok almost done now the bolt of the bey. You can't clean the top of the bolt because of the sticker but u can under. Get a paper towel and dampen it a bit with hot water or cold either is fine. Where the screw part is clean it with the damp paper towel. Then You are done. =D The final and last step is to re-assemble your bey and put it in the plate if u want to let it rest. Thank you so much for reading to the end.
Materials:
-Sink
-Water hot
-A small container that can hold hot water
-Any liquid soap any kind
-Paper Towels
( optional )
-2 rags
-Brasso-they can be found at fred meyer at the grocery section
-A paper plate to put your beyblades on and letting them rest for a while
-First off you dis-asemble your beyblade line up the parts from bolt to bottom to see all the parts you have and won't lose track any of your parts. The next thing is grab the bottom and track parts of the beyblade ( the two parts at the bottom of the bey ) You can also grab the clear wheel of the bey if you don't really care of the stickers coming off. Go to your sink and put of your hands and put liquid hand soap on your beyblade parts like your washing your hands. Your two hands scrubbing each other like washing hands with the parts inside and with soap don't add water yet. Once u Scrubbed them enough use the water that's mid-hot so you won't burn your hands. Make sure the parts have no soap in them. Then Fill up your container with hot water, enough to sink the parts. Then put your parts in. While their in the water. This is optional cleaning your fusion wheel if you want too but i mostly do it. Fusion wheels i think are made out of stainless steel. So i use brasso it cleans and polishes so it's perfect. Grab one rag and put the brasso on it and put it on your beyblade. Then once it's on the sides and bottom and top clean the brasso with the dry rag. And there you go your polished fusion wheel. Ok let's get back to your parts that are in the water. Grab your parts and get the water off using your paper towels. Ok almost done now the bolt of the bey. You can't clean the top of the bolt because of the sticker but u can under. Get a paper towel and dampen it a bit with hot water or cold either is fine. Where the screw part is clean it with the damp paper towel. Then You are done. =D The final and last step is to re-assemble your bey and put it in the plate if u want to let it rest. Thank you so much for reading to the end.
![[Image: s-pegasis-Userbar.jpg]](https://i835.photobucket.com/albums/zz274/RobstaOne/Userbars/s-pegasis-Userbar.jpg)
Thanks Robsta!![[Image: eruXp.png]](https://i.imgur.com/eruXp.png)
![[Image: uKF94LK.gif]](https://i.imgur.com/uKF94LK.gif)
